0:00 Coldstart A Coldstart is done on the beginning of each switch on time. A Coldstart can happen only, if the VBar
Units is disconnected from power for more than 5 Seconds.
0:00 Reset Reason: Power
On
This happens if power is applied to the VBar unit. Usually this is ok, but it shall never happen in
operational mode. So if a reset happens during flight, this points to a power problem. During flight the
power on reset results in a warmstart. If a coldstart happens during flight, the power loss was more
than 5 Seconds
0:00 Bank 0 Loaded Bank 0 was loaded from the non volatile memory. This can be triggered my manual backswitch from
the userinterface as well as in flight if bank switch is programmed to the aux channel. On Startup the
Bank 0 is loaded by default.
0:05 Calibration Finished At each Coldstart, the sensor and RC Values are calibrated to the actual seen values. If the calibration
is finished, this message confirms the storage of data into the internal non volatile calibration memory
0:15 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
0:25 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
0:35 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
0:45 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
0:55 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
1:05 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
1:15 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
1:25 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
1:35 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
1:45 Raised Vibration Level There was detected a raised level of Vibration. Since the vibration detector has to decide which signal
is vibration and chis is the intended measurement signal, this can happen sometimes on hard 3d
moves. It shall not happen all the time. If this error is reported repedidtly very often, check the heli for
vibration sources.
1:55 High Vibration Level The control loop suffers from a high vibration level, that starts to render the sensors blind. Save flying
is possible, but the stability will be degraded. Additinally slow drifts that happen may be caused by
vibrations.
2:05 High Vibration Level The control loop suffers from a high vibration level, that starts to render the sensors blind. Save flying
is possible, but the stability will be degraded. Additinally slow drifts that happen may be caused by
vibrations.
2:14 Extreme Vibration
Level
Vibrations are extreme. That means, that the measurement signal is much lower than the signal level
of the vibrations. No usable flying is possible with this level. Everything has to be checked and
extended tests are needed to isolate and eliminate the source of vibrations
2:24 High Vibration Level The control loop suffers from a high vibration level, that starts to render the sensors blind. Save flying
is possible, but the stability will be degraded. Additinally slow drifts that happen may be caused by
vibrations.
2:29 Antenna Switched The Signal from one of the sattelites was missing. The Main reciver is switched over to the other
connector. In Case of a single reciver connected, one frame was lost.
2:29 RC Input of Pitch
Channel missed
The Pitch Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems
2:29 RC Input of Aileron
Channel missed
The Aileron Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if
for 50ms no new signal arrives from the reciver. Depending on the hardware connection this can point
to a problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels
will be accused at the same time. In case of single channels, this can happen seperately on each
channel. Closely check your wiring for broken wires or connection problems
2:29 RC Input of Elevator
Channel missed
The Elevator Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if
for 50ms no new signal arrives from the reciver. Depending on the hardware connection this can point
to a problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels
will be accused at the same time. In case of single channels, this can happen seperately on each
channel. Closely check your wiring for broken wires or connection problems
2:29 RC Input of Tail
Channel missed
The Tail Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems
2:29 RC Input of AUX
Channel missed
The AUX Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems. The aux channel is monitored only
in case it is used by the bank selekt switch
2:30 Aileron Sensor Value
out of Range
The Sensor delivers Values that are not trustful. Rotational rates, that will create this values are
usually not possible in air. The Sensor may be defective. This can happen in certain cases if the heli is
handleled on ground, or on very hard landings or very extreme Vibrations.
2:30 Elevator Sensor Value
out of Range
The Sensor delivers Values that are not trustful. Rotational rates, that will create this values are
usually not possible in air. The Sensor may be defective. This can happen in certain cases if the heli is
handleled on ground, or on very hard landings or very extreme Vibrations.
2:33 Extreme Vibration
Level
Vibrations are extreme. That means, that the measurement signal is much lower than the signal level
of the vibrations. No usable flying is possible with this level. Everything has to be checked and
extended tests are needed to isolate and eliminate the source of vibrations
2:43 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
2:53 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
3:03 Good Health Message
(10sec)
This Message describes the good health state. That means, that the VBar unit does not see any error
or Info Message in the last 10 Seconds.
3:10 Antenna Switched The Signal from one of the sattelites was missing. The Main reciver is switched over to the other
connector. In Case of a single reciver connected, one frame was lost.
3:10 RC Input of Pitch
Channel missed
The Pitch Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems
3:10 RC Input of Aileron
Channel missed
The Aileron Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if
for 50ms no new signal arrives from the reciver. Depending on the hardware connection this can point
to a problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels
will be accused at the same time. In case of single channels, this can happen seperately on each
channel. Closely check your wiring for broken wires or connection problems
3:10 RC Input of Elevator
Channel missed
The Elevator Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if
for 50ms no new signal arrives from the reciver. Depending on the hardware connection this can point
to a problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels
will be accused at the same time. In case of single channels, this can happen seperately on each
channel. Closely check your wiring for broken wires or connection problems
3:10 RC Input of Tail
Channel missed
The Tail Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems
3:10 RC Input of AUX
Channel missed
The AUX Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems. The aux channel is monitored only
in case it is used by the bank selekt switch
3:11 Antenna Switched The Signal from one of the sattelites was missing. The Main reciver is switched over to the other
connector. In Case of a single reciver connected, one frame was lost.
3:11 RC Input of Pitch
Channel missed
The Pitch Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems
3:11 RC Input of Aileron
Channel missed
The Aileron Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if
for 50ms no new signal arrives from the reciver. Depending on the hardware connection this can point
to a problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels
will be accused at the same time. In case of single channels, this can happen seperately on each
channel. Closely check your wiring for broken wires or connection problems
3:11 RC Input of Elevator
Channel missed
The Elevator Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if
for 50ms no new signal arrives from the reciver. Depending on the hardware connection this can point
to a problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels
will be accused at the same time. In case of single channels, this can happen seperately on each
channel. Closely check your wiring for broken wires or connection problems
3:11 RC Input of Tail
Channel missed
The Tail Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems
3:11 RC Input of AUX
Channel missed
The AUX Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems. The aux channel is monitored only
in case it is used by the bank selekt switch
3:12 Antenna Switched The Signal from one of the sattelites was missing. The Main reciver is switched over to the other
connector. In Case of a single reciver connected, one frame was lost.
3:12 RC Input of Pitch
Channel missed
The Pitch Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems
3:12 RC Input of Aileron
Channel missed
The Aileron Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if
for 50ms no new signal arrives from the reciver. Depending on the hardware connection this can point
to a problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels
will be accused at the same time. In case of single channels, this can happen seperately on each
channel. Closely check your wiring for broken wires or connection problems
3:12 RC Input of Elevator
Channel missed
The Elevator Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if
for 50ms no new signal arrives from the reciver. Depending on the hardware connection this can point
to a problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels
will be accused at the same time. In case of single channels, this can happen seperately on each
channel. Closely check your wiring for broken wires or connection problems
3:12 RC Input of Tail
Channel missed
The Tail Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems
3:12 RC Input of AUX
Channel missed
The AUX Input Signal ist updated with each Frame recived from the reciver. This Error is raised, if for
50ms no new signal arrives from the reciver. Depending on the hardware connection this can point to a
problem with the connection to the reciver/sattelite. In case of sattelite recivers used, all channels will
be accused at the same time. In case of single channels, this can happen seperately on each channel.
Closely check your wiring for broken wires or connection problems. The aux channel is monitored only
in case it is used by the bank selekt switch